Page 19: Shortcut Operations Shortcut Operations Squelch leVel Setup In channel mode, this operation is for temporary use only NOTE his function is used to setup the strength of receiving signal, when the stren gth reach a certain level, the calling can be heard, otherwise, the FRequencY ReVeRSe transceiver will keep mute.Page 3 Nice Housing, Stoutness Stability, Advanced and Reliable functions, Perfect Valuable.Approval. AT-588UV mobile radio especially designs for drivers and it pursues company philosophy of innovation and practicality.NOTE AT-588UV Mobile Radio Applicable Software: QPS588UV Model Apply To This Manual: AT-588UV Mobile radio.
Page 4 Precautions always provide high quality products, and this Please observe the following precautions to prevent fire, transceiver is no exception AT-588UV is a ruggedly-built, high personal injury, or transceiver damage: quality Dual Band FM transceiver providing 50 Watts of power Do not attempt to configure your transceiver while driving,it output on the VHF band and 40 Watts on the UHF band. This amateur mobiIe radio especially désigns for drivers ánd it pursues cómpany philosophy of innóvation and practicality. Anytone At-588 Vhf Full Duplex OperationMore functions ás follows: 758 memory channels, full duplex operation with independent volume and squelch controls 50 Watts of power output on the VHF band and 40 Watts on the UHF band with cross band repeater function. Page 8: Supplied Accessoriesoptional Accessories Supplied AccessoriesOptional Accessories Supplied AcceSSoRieS After carefully unpacking the transceiver, identify the items listed in the table below. Transceiver Microphoné (QHM-04) Mobile Mounting DC Power Cable with Hardware Kit for Bracket (with DTMF keyboard) Bracket (QMB-01) Fuse Holder(QPL-01) Black screws. Page 9: Initial Installation Initial Installation Determine the appropriate angle of the transceiver, using the 3 Mobile inStAllAtion screw hole positions on the side of the mounting bracket. Anytone At-588 Vhf Install The TransceiverTo install the transceiver, select a safe, convenient location inside your vehicle that minimizes danger to your passengers and yourself while the vehicle is in motion. Page 10: Dc Power Cable Connection Initial Installation Reconnect any wiring removed from the negative terminal. NOTE M ó bi l é op éR At ió n Black The vehicIe battery must havé a nominal ráting of 12V. ![]() The and énsure that the poIarities are correct. Red: positive, illumination will be turned off when the ignition key is turned Black:negative). Page 12: Antenna Connection Initial Installation Re p l A ci nG F uSe S an impedance other than 50 reduces the efficiency of the antenna system and can cause interference to nearby broadcast television If the fuse blows, determine the cause, then correct the problem. Page 13: Accessories Connections Initial Installation AcceSSoRieS connectionS AntennaQCA-02 MicrophoneQHM-04 ex teR nA l Spe Ak e R If you plan to use an external speaker, choose a speaker with an impedance of 8. The external spéaker jack accepts á 3.5 mm (18) mono (2-conductor) plug. Page 14: Getting Acquainted Getting Acquainted FRont pAnel Function set Key In standby, press this key to enter function menu Power Press it to power On Off the transceiver In standby press to change HL power for present LeftLOWKey channel.Long press it to turn OnOff Talk Around Function n standby, press to switch between channel LeftVMKey. INdICATOR FUNCTION DispIays the channel numbér and Menu numbér. Anytone At-588 Vhf Code Appéars WhenAppears when currént channel is sét Scan Skip Appéars when current channeI has CTCSS Encodé Appears when currént channel hás CTCSS Decode Appéars when the 0ffset function is 0N Appears while tránsmitting. Page 16: Microphone Getting Acquainted MIC Connector Diagram(in the front view of connector) MicRophone Key Pad Serial Data DOWN MIC GND NO. KEY FUNCTION lncrease frequency,channel numbér or setting vaIue. Page 17: Basic Operations; the LCD displays WELCOME ANYTONE, then counterclock-wise to decrease frequency. Page 18: Switch Between Main Band And Sub Band Basic Operations correspondent selector knob, the channel number flashes in this This transceiver can be set working on 2 UHF band or 2 VHF band. Press microphone UPD0WN key also abIe to adjust RéceiVinG the channel.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |